RK3588 Custom Android Smart Display, WF-C3588-M2, AndroidSBC, Fort Worth

TL;DR: RK3588 Custom Android Smart Display

LONGGANG, Shenzhen, September 12, 2026 - The Rockchip RK3588 line at Wanlin Longgang closed lot 159 this week: 31,535 WF-C3588-M2 boards bound for Fort Worth, United States, each unit traceable to its own burn-in barcode.

AndroidSBC shipping and Incoterm briefing for WF-C3588 custom board orders serving Fort Worth, United States. The WF-C3588 line is a custom motherboard programme built on the Rockchip RK3588 octa-core platform (4x Cortex-A76 at 2.4GHz plus 4x Cortex-A55 at 1.8GHz on 8nm) with a triple-core NPU delivering 6 TOPS of INT8 inference, 8K H.265 decode and up to 32GB of LPDDR4X or LPDDR5. AndroidSBC, the export arm of Wanlin Manufacturing Group, builds nine custom variants at the Longgang source factory in Shenzhen for Fort Worth and United States buyers: WF-C3588-A0 custom Android motherboards, WF-C3588-I1 custom industrial boards, WF-C3588-M2 core boards and SOMs with carrier design, WF-C3588-S3 custom signage and video wall boards, WF-C3588-K4 custom kiosk and POS boards, WF-C3588-R5 custom robotics controllers, WF-C3588-N6 custom NVR boards, WF-C3588-E7 custom edge AI boards, and WF-C3588-P8 custom ARM PC and NAS boards.

About AndroidSBC and the Rockchip RK3588 Board Family

The WF-C3588 is a nine-variant custom motherboard programme from AndroidSBC, the export arm of Wanlin Manufacturing Group in Shenzhen. One Rockchip RK3588 silicon, nine custom categories: custom Android motherboards, custom industrial boards, core board and SOM work, custom signage and video wall boards, custom kiosk and POS boards, custom robotics controllers, custom NVR boards, custom edge AI boards, and custom ARM PC and NAS boards. Wanlin's Longgang plant handles SMT, burn-in and pre-shipment inspection in one building, and the export desk handles the CE, FCC, UKCA, RoHS and IEC 62368-1 file per lot. For United States importers, the line covers the custom board categories a Fort Worth distributor is most often asked to quote.

WF-C3588-M2 Technical Specifications

All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-C3588-M2 (Custom Core Board SOM with Carrier Board Design Service) holds its display output and its decoder load at the same time through the burn-in loop, a combination that the legacy boards in the comparison column cannot sustain. For United States importers sourcing the WF-Series, the 16GB + 64GB (WF-C3588-M2-C) variant is the typical configuration for the custom core board and SOM plus carrier programmes use case, with a sustained weekly capacity of 5,000 pcs/wk on the Longgang line.

Challenges in Sourcing Custom Core Board SOM with Carrier Board Design Service for United States Buyers

Buyers in Fort Worth who have run the custom core board som with carrier board design service category for a few years tend to stop shopping on price alone. The Rockchip RK3588 allocation is the real constraint, and it is the reason a 31,535-unit order can look cheap on paper and expensive in a slipped quarter. The software question follows immediately. The hardware spec sheet is easy to verify; the difference between a board that runs a launcher and a board that holds a certified, credential-locked stack only becomes visible after the first field update.

Documentation closes the list. Buyers in Fort Worth have learned to ask for the test reports before the deposit, because a CE mark printed on a carton is worth nothing at the port without the Declaration of Conformity behind it. AndroidSBC moves all three risks inside the factory: the custom variant is assembled at Longgang, the certified image is burned on the same line, and the Technical File ships with the lot. Across the nine WF-C3588 variants the coverage runs from SMARC 2.2 modules, stamp-hole core boards, LGA core boards, COM Express carriers, medical imaging terminals, robotics compute modules, custom carrier designs, and OEM development kits, with three memory configurations per variant, so a Fort Worth buyer can usually match a requirement from the standard custom range.

The United States paperwork question is settled before production. In the United States FCC Part 15 authorisation is required and an FCC ID applies to radio modules, while UL or ETL listing is usually demanded by the retail channel. The Longgang export desk prepares the destination-market file covering FCC Part 15 authorisation with an FCC ID for radio modules and a UL or ETL listing administered by FCC / UL and releases it with the standard multi-market pack (CE, FCC, UKCA, RoHS, REACH), booking the lot into Port of Los Angeles on the Los Angeles to Yantian lane.

Competitive Comparison: WF-C3588-M2 vs Competing RK3588 Boards

The comparison set for the custom core board som with carrier board design service socket breaks three ways: catalogue boards with fixed I/O and no engineering support, re-badged imports with a sticker but no schematic, and source-factory custom boards that carry the BSP, the test bench and the certification desk in-house. The WF-C3588-M2 is in the last group, and the separation comes from Rockchip RK3588, from customization depth, and from the per-lot certified image burn.

• vs standard SOM catalogues: the WF-C3588-M2 either matches SMARC 2.2 exactly or the carrier is redesigned around the project, so the module never forces the product.
• vs two-vendor module plus carrier splits: core board and carrier come from one desk, one schematic review and one test plan, which removes the finger-pointing stage entirely.
• vs closed-module vendors: BSP source, SDK and documentation ship with the project, so a customer engineering team can maintain the carrier after delivery.
• vs re-branded modules: the SI report and the thermal map are Longgang documents, not forwarded PDFs from a third party.

Global Custom SOM and Core Board Market Trends

Order timing in United States now follows the Custom SOM and Core Board curve rather than the old annual budget cycle. MarketsandMarkets sizes the Edge AI hardware segment at USD 26.9 billion for 2025 with a 32.7 percent CAGR to USD 108.2 billion by 2030 (MarketsandMarkets, 2025-2030), and that growth is the reference point United States buyers use when they argue about RK3588 allocation. In Fort Worth, it shows up as three distinct demand patterns across the WF-C3588:

• Medical imaging terminal: a device maker keeps its regulatory file intact by swapping the core board and reusing the validated carrier.
• Display and signage refresh cycles: a longer content loop and a higher panel resolution now define the refresh trigger. The WF-C3588-M2 board carries that headroom without a board change.
• Custom SMARC migration: a legacy SMARC installation moves to RK3588 with a pin-compatible carrier revision and keeps the enclosure.

For the Custom SOM and Core Board category the practical signal in United States is that framework agreements are replacing spot buying, and the agreements are getting longer.

Read together, the three patterns explain the move in Fort Worth from spot quotes to framework agreements released monthly, which is what a custom RK3588 motherboard programme needs to hold a twelve-month shipping window without a mid-year break.

Partner Success Story: Ostra Vision Labs in Fort Worth, United States

Ostra Vision Labs, a machine vision integrator serving the United States market, deployed 4,900 custom WF-C3588-E7 edge AI boards for factory inspection lines. The rollout covered the medical imaging terminal, custom smarc migration, and machine vision carrier workloads, with AndroidSBC handling the burn-in, the certification scope, and the palletisation at the Wanlin Longgang plant.

• Deployed: 4,900 custom WF-C3588-E7 edge AI boards for factory inspection lines
• Region: Fort Worth, United States
• Models used: WF-C3588-M2 (lead SKU), plus eight sibling custom RK3588 board variants in the same platform family
• Certifications handled: CE, FCC, UKCA, RoHS, REACH, IEC 62368-1, EN 55032, EN 55035, plus optional UL 60950-1, GMS, Widevine L1 and Dolby Audio per variant
• Logistics: FOB Qingdao with the Wanlin Group Longgang source factory named on the export declaration, entering Port of Los Angeles via the Los Angeles to Yantian lane

"Our defect model went from ONNX to RKNN inside a week with their engineering desk, not a forum thread. The boards run four cameras per cell with classification at line speed, and the per-unit barcode makes every RMA a root-cause report instead of a swap."

- Daniel Reyes, VP Product

Field Report: a high-brightness outdoor display trial in Fort Worth, where 31,535 units of the WF-C3588-M2 board are running behind sunlight-readable panels

Reporter Yu Cheng, on the ground in Fort Worth, United States. The trial ran the WF-C3588-M2 boards inside a sealed enclosure with no active cooling and a panel brightness pushed to its ceiling. Internal board temperature stabilised below the throttle point across a full day of direct sun, and the content loop ran without a dropped frame from morning to evening.

A spare-parts kit was packed alongside the order so the destination depot could swap a board without waiting on a cross-border shipment.

The inspection confirmed three things on the spot: the WF-C3588-M2 units hold the burn-in with a yield above 99.06 percent, the loaded firmware image survives a 72-hour continuous loop without credential drift, and the pallets carry the matching certification file for the destination market, covering FCC Part 15 authorisation with an FCC ID for radio modules and a UL or ETL listing administered by FCC / UL, cleared for entry at Port of Los Angeles on the Los Angeles to Yantian lane. Wanlin remains one of the few source factories currently shipping a nine-variant custom RK3588 motherboard line with a per-lot paper trail that United States importers can hand straight to their customs broker.

Filed by Yu Cheng, AndroidSBC field reporter, Wanlin Manufacturing Group export base.

WF-C3588-M2 Application Scenarios

The WF-C3588 line fits nine custom motherboard lanes, with the WF-C3588-M2 (Custom Core Board SOM with Carrier Board Design Service) as the lead SKU for Fort Worth and United States programmes:

• Medical imaging terminal: a device maker keeps its regulatory file intact by swapping the core board and reusing the validated carrier.
• Robotics compute module: an AMR maker takes the stamp-hole core board and designs a slim carrier for a new chassis generation.
• Custom SMARC migration: a legacy SMARC installation moves to RK3588 with a pin-compatible carrier revision and keeps the enclosure.
• OEM development kit: a product team gets the reference carrier, the SDK and the BSP source and prototypes before committing to tooling.
• LGA core board programme: a display brand solders the core board directly onto its own mainboard for a locked BOM.
• Machine vision carrier: a vision integrator routes MIPI CSI-2 lanes to four cameras and lets the NPU carry the inspection model.
• Fleet compute module: a telematics supplier builds one carrier for three vehicle programmes and swaps memory options per contract.
• Lab instrumentation: an instrument maker keeps a decade-old enclosure alive by replacing only the core board and the BSP.

Partnership Models for Fort Worth Buyers

Three commercial structures are open to Fort Worth buyers on the WF-C3588-M2 and the rest of the WF-C3588 custom variants:

• OEM (your brand on our hardware): custom logo silk-print, custom packaging, custom boot animation, custom SKU label, and a private-label certification file.
• ODM (your spec on our reference design): schematic and stack-up review, carrier or motherboard redesign, custom firmware features, and a BSP port handled by the Longgang engineering desk.
• Distribution (your channel, our stock): regional distributor rights, channel rebate, stock holding at the factory, and a framework agreement with a monthly lot release.

The three tiers share one factory, one test flow and one certification file. For Fort Worth buyers the standard entry point on the WF-C3588-M2 is the 16GB + 64GB (WF-C3588-M2-C) configuration at MOQ 5,000 units per shipment, 1-3 days to sample on standard variants and 15-30 days to mass production.

Frequently Asked Questions

What exactly can be customised on an RK3588 motherboard from AndroidSBC?

Answer: Practically the layers that decide whether the board fits your product: the PCB layout and outline, the memory and storage fit (4GB to 32GB LPDDR4X/LPDDR5, eMMC to 128GB plus NVMe or SATA), the display interface mix (HDMI 2.1, DP 1.4, LVDS/eDP/MIPI), the I/O bank (CAN, RS232/RS485 multi-serial, relays, digital I/O), the wireless stack, and the enclosure or DIN-rail chassis. On top of that sit the firmware options: custom Android ROM with a locked launcher, custom Linux or Yocto image, pre-installed applications, custom boot animation and OTA updates. A United States buyer can start from a standard WF-C3588 variant and change one layer, or bring a full schematic and have the carrier designed from scratch.

Can AndroidSBC port a custom Android ROM or a custom Linux BSP to our carrier board?

Answer: Yes. Under NDA, AndroidSBC delivers custom Android ROM work with proprietary services and a locked launcher, custom Linux images on Ubuntu, Debian, Yocto or Buildroot, BSP ports for customer carriers, and driver development for project-specific I/O. Source access is released to the partner, and the port is performed at Longgang, which matters because a vendor BSP rarely matches a custom carrier revision on the first try.

Can the 6 TOPS NPU on a custom board run our own AI models?

Answer: The NPU is fully open on the custom line. Bring the model in PyTorch, ONNX, TensorFlow or Caffe and the Longgang desk handles the RKNN quantization, the runtime integration and the validation against your board's thermal and memory profile. Custom AI algorithm integration is a standard line item on the ODM scope, and the resulting model ships embedded in the firmware image burned per lot.

What are the MOQ and lead times for a custom RK3588 motherboard?

Answer: Standard-variant samples ship in 1-3 days from stock, so your engineering team can start integration while the custom scope is being quoted. A custom run follows a 15-30 day mass-production window after schematic and stack-up sign-off. MOQ is 5,000 units per shipment on standard variants; on custom configurations the MOQ is negotiable against volume commitments, and small batch orders are accepted for pilot phases. A twelve-month framework agreement with monthly lot releases brings the per-lot MOQ down further.

What certifications does a custom board need for United States, and who handles them?

Answer: Yes, and the file travels with the goods. The pack covers CE, FCC Part 15, UKCA, RoHS 2.0, REACH and IEC 62368-1 with the EMC and safety reports for your configuration, dated within the prior year. AndroidSBC confirms any United States-specific addition at quotation stage, which is the point where the answer is still useful rather than expensive.

How long will AndroidSBC keep supplying a custom board?

Answer: Seven years minimum supply, patches maintained across the firmware lines, OTA for firmware and NPU model updates. For a United States programme running a custom board in the field, that commitment is written into the agreement at signature, which is what separates a source factory from a catalogue reseller.

Can AndroidSBC ship custom boards to Amazon FBA warehouses or 3PL consolidation points?

Answer: Yes, including DDP into Amazon FBA in the US, EU and Japan, plus 3PL consolidation points in Hong Kong, Singapore, Rotterdam, Los Angeles and Shenzhen. Cartons are labelled to FBA inbound spec and the declaration names Longgang as the origin. Partners who consolidate in Hong Kong usually take FOB Yantian and handle the last leg themselves.

How does AndroidSBC handle RMA or DOA replacements on custom boards?

Answer: AndroidSBC targets a 0.3 percent DOA rate across the WF-C3588 line, measured over the prior twelve months. On RMA, the partner returns the faulty WF-C3588-M2 unit to Longgang with its burn-in barcode, and a replacement ships within ten business days. Because the burn-in record and the configuration file are attached per unit, the failure analysis normally comes back with a root cause rather than a credit note, which matters when a custom configuration is holding up a production line.

Contact AndroidSBC: Start Your WF-C3588-M2 Sourcing Conversation

The AndroidSBC export desk handles all WF-C3588 enquiries from Fort Worth and United States. Direct factory contact on the WF-C3588-M2 and the rest of the custom core board som with carrier board design service line is available through:

• Email: Androidsbc@163.com
• Export service hotline: +8613261677119
• Website: https://www.androidsbc.com
• Destination market file: FCC Part 15 authorisation with an FCC ID for radio modules and a UL or ETL listing for United States, administered by FCC / UL, entering at Port of Los Angeles on the Los Angeles to Yantian lane
• Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China

OEM and ODM enquiries move fastest when the first message carries the annual volume, the customization scope and the Incoterm. Send those three and the export desk replies with a per-lot quote and the full WF-C3588 MOQ matrix inside two business days.